Snap-on TEX1503TL torque wrench, Torqometer U.S. light signal T-handle dial head, 1,500 ft-lb, 1 inch drive

Snap-on TEX1503TL Torque Wrench, Torqometer U.S. Light Signal T-Handle, 1,500 ft-lb, 1″ Drive

Name: Snap-on TEX1503TL Torque Wrench, Torqometer U.S. Light Signal T-Handle, 1,500 ft-lb, 1" Drive
Brand: Snap-on
SKU: LIH-TEX1503TL
Availability: InStock

The Snap-on TEX1503TL torque wrench is a U.S.-reading Torqometer T-handle head with a lamp that lights at the preset value. It reads to 1,500 ft-lb in 25 ft-lb steps on 1 inch input and output drives. Lost in HCM supplies it.

SKU: LIH-TEX1503TL

Category: Torque Wrenches

Brands: Snap-on

Description

Industrial parks across Vietnam keep adding steel-frame factories and warehouses. Erection crews join base plates, columns, rafters and crane girders with large bolts, often while standing in a boom lift. The Snap-on TEX1503TL torque wrench helps them hit a preset value without staring at a dial. It is a U.S.-reading Torqometer T-handle head, and a lamp lights when the pull reaches the target.

Steel frame bolting with the Snap-on TEX1503TL torque wrench

Frame drawings set the bolt grade and the tightening method for each joint. When the engineer calls for torque, the crew sets the head, fits the socket, and pulls until the lamp shows. Then they move to the next bolt in the pattern. Because the cue is visual, a fitter can watch the socket and the joint rather than the face of the head.

What CAT1500i prints for the TEX1503TL

Feature	TEX1503TL
Input drive	1 in female square
Output drive	1 in male square
U.S. range	1,500 ft-lb
Increments	25 ft-lb
Length / width / head depth	10-7/8 in / 4-3/8 in / 4-7/16 in
Optional handles	82TQP T bar (18 in), 85TQP extension (31 in)

These figures sit in the U.S. Reading T-handle table of Snap-on catalog CAT1500i. In addition, the same row names the TEX1503TFU as its follow-up twin. Snap-on also notes that table models come without a certificate, while a C on the stock number adds one.

A lamp you can see from a boom lift

Because wind and noise fill the air high on a frame, a fine dial turns hard to read. However, a light shows clearly even from an awkward angle. So the TEX1503TL suits repeat bolts where the crew needs a quick yes at each one. In addition, it reduces overshoot, since the fitter stops pulling as soon as the light appears.

Range plan for the TEX1503TL

Snap-on rates this grade to 2% of reading between 20% of full scale and full scale. For this head, that means 300 to 1,500 ft-lb, so the top equals about 2,030 N·m. Smaller bracket and purlin bolts fall below the band, so pair the head with a smaller wrench. Also note that many structural joints use turn-of-nut or tension-control bolts instead of torque.

Daily checks for the Snap-on TEX1503TL torque wrench

First, test the lamp before the crew goes up.
Tie the head and handle to a rated lanyard when working at height.
Keep rain and grit off the dial, then dry it at the end of the day.
Never pull past 1,500 ft-lb or use it to loosen seized nuts.

Then book the TEX1503TL for calibration on your company cycle.

Quote for the TEX1503TL from Lost in HCM

Lost in HCM supplies the head and prepares each quote. For an erection contractor or a plant engineering team, request a quote from Lost in HCM. More heads appear under torque wrenches on SMK Vietnam. See snapon.com for maker data, or contact SMK Vietnam.