Description
This page covers the Snap-on TESI2803L Torqometer under its plain code, as Lost in HCM lists it: “Newton Meter Light Signal – TESI2803L”. So no certificate wording appears in that name. If your plant needs one on arrival, see the TESI2803LC listing with a calibration certificate. Both codes point to the same 1 inch drive dial wrench.
Plain code or LC: let the paperwork decide
Snap-on’s CAT1500i table for this wrench carries a short rule. Its stock numbers ship without a certificate of calibration, and a C at the end orders one. So the TESI2803L and the TESI2803LC share the dial, the lamp and the frame. As a result, only the document differs.
| Your situation | Better code |
|---|---|
| Own torque bench verifies every new tool | TESI2803L |
| Contract lab checks tools before first use | TESI2803L |
| Auditor wants a record from day one | TESI2803LC |
| Receiving holds any gauge that lacks a document | TESI2803LC |
| Tight budget, with a master tool on site for cross-checks | TESI2803L |
Where a 2,800 N·m lamp wrench earns its keep
Cement plants, steel mills and thermal power stations run big gear drives, mill bases and fan housings. During a planned stop, crews bring those heavy joints back to the maker’s values. In a kiln hall or on a turbine deck, though, noise and dust make a dial hard to watch. The Snap-on TESI2803L Torqometer answers that, because its built-in light flashes when the pull reaches the targeted torque. The fitter then reads the needle for the log sheet.
Frame data behind the Snap-on TESI2803L Torqometer
- Drive: 1 inch square, sized for heavy sockets.
- Scale: 2,800 N·m in 50 N·m steps, about 2,065 ft-lb.
- Length: 80 in, so plan for two people.
- Head: 4-13/32 in wide and 2-1/8 in deep.
- Catalog table: Newton Meter Reading/Standard 2% Accuracy, CAT1500i p.334.
Snap-on’s UK brochure gives Torqometer accuracy as within 2% of reading from 20% of full scale up, in both directions. On this dial, that span opens at 560 N·m. For lighter bolts, a smaller TESI frame keeps the job nearer mid-scale, as the brochure advises.
Handling an 80 inch frame
Plan a clear swing path before each pull, and use two people when space runs short. Also take the load slowly, so the needle and lamp keep pace with your hands. Snap-on warns against going past rated torque or freeing stuck bolts with a Torqometer. Therefore crack seized nuts on the drive with a slugging wrench first. Finally, book a recheck of the TESI2803L at your usual interval, since Snap-on says periodic recalibration keeps it accurate.
Getting a price on the Snap-on TESI2803L Torqometer
Lost in HCM supplies Snap-on dial wrenches across Vietnam and prepares each quote for SMK Vietnam buyers. Write TESI2803L on your request, so the plain code ships. After that, request a quote from Lost in HCM and name your site. You can also compare frames in our torque wrenches range, visit snapon.com, or contact SMK Vietnam.
TESI2803L shutdown questions
Can our own lab certify the TESI2803L later?
Your lab or an outside lab can check it and write its own report. However, the Snap-on certificate only comes with the LC code.
Will the needle stay at the peak?
No. This code sits in the Signal column, so it flashes a lamp rather than leaving a second needle behind. Snap-on lists a TESI2803FU follow-up code in the same row.
Which extension handle ships with it?
Our copy of the catalog footnote for this code does not read clearly. So ask Lost in HCM to confirm the box contents first.
Reviews
There are no reviews yet.