Description
Urea and ammonia plants in Vietnam, such as those at Phu My and Ca Mau, stop for planned turnarounds. In a few weeks, crews open compressors, pumps and granulators, then close them again to spec. The Snap-on TE2003FUC Torqometer takes on the heaviest of those bolts. It is a 1-inch drive dial wrench with two needles and a 2,000 ft-lb scale.
Turnaround joints for the TE2003FUC
- Compressor and turbine baseplate hold-down bolts, where the OEM gives a value.
- Large pump casing and base bolts.
- Granulator, crusher and conveyor drive gearbox bolts.
- Bucket elevator head and screw conveyor bearing bolts.
Process flanges on high-pressure loops follow the plant’s bolting procedure, which may call for tensioners. So the TE2003FUC fits rotating and bulk-handling joints with a printed ft-lb value.
TE2003FU specs in the Snap-on catalog
| Item | TE2003FU (CAT1500i p.333) |
|---|---|
| Square drive | 1 in |
| Range | 2,000 ft-lb |
| Increments | 25 ft-lb |
| Length | 80 in |
| Width | 4-13/32 in |
| Head depth | 2-1/8 in |
| Extension handle | 93TQPA 5 ft tubular, packed separately |
The row above comes from Snap-on’s US Reading/Standard 2% Accuracy table. That page says certificate of calibration models add a C suffix. The TE2003FUC is therefore that C version of the TE2003FU. Lost in HCM titles it with Chart, so ask what papers come with it.
Follow-up needles for a crowded schedule
Turnaround crews work in shifts, and each joint needs a record before handover. The Snap-on TE2003FUC Torqometer shows the targeted torque on one needle and the torque achieved on the other. So the reading survives after the fitter lets go. A supervisor can then confirm it before signing the job card.
Choosing the Snap-on TE2003FUC Torqometer or a 1-1/2 inch model
Snap-on also lists a TE2005FU with the same 2,000 ft-lb scale on a 1-1/2 inch drive. The TE2003FUC suits plants whose big sockets have 1 inch squares. Its head depth of 2-1/8 inches is also a little slimmer, against 2-3/8 inches on the larger drive. So pick the drive that matches your socket set.
Accuracy band and care
Lost in HCM lists this wrench under US Reading/Standard 2% Accuracy. Snap-on’s Standard grade means within 2% of reading from 20% of full scale to full scale, so this band starts at 400 ft-lb. Urea dust and damp air also corrode steel, so wipe the TE2003FUC clean after each shift. Do not use it to crack a stuck nut free, and book periodic recalibration with an outside lab.
Order the Snap-on TE2003FUC Torqometer
Fertilizer producers, turnaround contractors and chemical plants can order this wrench from Lost in HCM, which supplies SMK Vietnam’s listing. To lock it in before your next shutdown, request a quote from Lost in HCM. Smaller dials appear under torque wrenches. You can also see snapon.com, or contact SMK Vietnam.
Turnaround FAQ for the TE2003FUC
Which handle ships with it?
The TE2003FU row carries a dagger note for a 93TQPA 5 foot tubular extension handle, packed on its own. Lost in HCM can confirm the box contents.
What is the TE2003FUC’s overall length?
Snap-on lists 80 inches for the base model, before you fit the extension handle.
Can it read N·m?
No. The dial reads ft-lb, and its 2,000 ft-lb top end works out to roughly 2,710 N·m.
Reviews
There are no reviews yet.