Description
Start at the bottom of the Snap-on IZO chart and you reach a 7 mm open end. The Snap-on IZ7OE9X12 torque insert is that part, the smallest tool Snap-on lists for the system. It locks into a 9 x 12 mm receiver, so a calibrated electronic wrench can take on M4-size nuts and tiny fittings.
What a 7 mm jaw reaches
Under ISO 4032, an M4 hex nut measures 7 mm across the flats. So the IZ7OE9X12 suits M4 nuts on sensor mounts, small covers and terminal hardware. It also slides onto a tiny tube nut from the side, where a ring could never pass over the line. Still, special parts can differ, so check the flats with a caliper before you order.
Bodies that accept the Snap-on IZ7OE9X12 torque insert
| Body | Fitting | Range, N·m | Length without head |
|---|---|---|---|
| CTECHAN30A | 9 x 12 mm | 1.50-30.00 | 338 mm |
| CTECHANM30 | 9 x 12 mm | 1.5-30 | Not listed |
| CTECHAN135A | 9 x 12 mm | 6.8-135.0 | 452 mm |
For a joint this small, the two 30 N·m bodies make the natural match for the IZ7OE9X12. Snap-on calibrates its wrenches for accuracy from 20 to 100% of full scale. On a 30 N·m body, that band begins at 6 N·m. Therefore, if your M4 value falls below 6 N·m, a torque screwdriver may suit the job better. By contrast, the CTECHAN135A would read such light values near the floor of its scale. In addition, the short CTECHAN30A fits inside cramped cabinets more easily than a longer body.
Fitting and setting the IZ7OE9X12
First, wipe the rectangular shank and push it into the receiver until the lock seats. Next, pick the head-length factor that ControlTech bodies store for different heads. Then set the target and pull slowly at the grip until the wrench signals. Also keep the jaw fully on the flats, because a 7 mm opening has little metal to spare.
Next sizes beside the Snap-on IZ7OE9X12 torque insert
- IZ8OE9X12, an 8 mm OE head for ISO M5 nuts.
- IZ10OE9X12, a 10 mm OE head for M6 hardware.
- IZ10IR9X12, the first insert ring, since no ring comes smaller.
Snap-on makes the 7 mm head for the 9 x 12 fitting only. As a result, a 14 x 18 body cannot take the IZ7OE9X12, and open ends for that fitting start at 13 mm.
Pricing an IZ7OE9X12 for your line
SMK Vietnam lists this insert as a partner part, while Lost in HCM supplies the IZ7OE9X12 and prepares the quote. Send your wrench model and the M4 torque value with the request. With those two facts in hand, request an IZ7OE9X12 quote from Lost in HCM. You can browse more torque wrench heads and adaptors or contact SMK Vietnam about fit.
Small-joint questions on the IZ7OE9X12
Which nut does a 7 mm OE head fit?
An ISO 4032 M4 hex nut, since it measures 7 mm across the flats.
Will a CTECHBN340A body take the IZ7OE9X12?
No. That body has a 14 x 18 mm receiver, while this insert uses the 9 x 12 mm fitting.
Is there a torque rating on the insert itself?
CAT1500i prints none for IZO inserts. So the wrench range sets the limit, and Snap-on warns against using the insert to break fasteners loose.
Reviews
There are no reviews yet.